Origninal Mini Moke Brochures Mini Moke USA Origninal Mini Moke Brochures

Mini Moke USA Home
Mini Moke History
Mini Moke Gallery
Mini Moke Videos
Mini Moke Links

USED ENGINE & RADIATOR BRACKET
This is a Good USED part that is not cracked, sripped or rusted away. Some have the "U" bracket to mount to radiator shroud. Similar to new one as pictured! This is the bracket that mounts the radiato

part no: U/12A361

12G940 CYLINDER HEAD, 9 OR ELEVEN STUD WITH VALVES & SPRINGS
Pre-Owned (Used) cylinder head is ideal candidate for a rebuild. Heads are available with holes for 9 stud but can be modified for 11 stud block. Cylinder heads are complete with valves and valve spr

part no: U/12G940

USED 1275CC CYLINDER HEAD WITH 1.4" INTAKE VALVES
Pre-Owned (Used) cylinder head is ideal candidate for a rebuild. Heads are available with holes for 9 stud but can be modified for 11 stud block. Cylinder heads are complete with valves and valve spr

part no: U/12G940BIG

ASSEMBLED MINI & MINI COOPER 1380 SHORTBLOCK
Big bore block, crank, rods and pistons. 1380 assembled shortblock consists of A-Plus block and crank machined to 73.5mm and assembled with pistons, rod bolts, bearings, and our special camshaft. We

part no: 1380/SHORTBLOCK

HEATER CONTROL VALVE STRAIGHT
This heater valve was used on several models of cars from BMC. Cable actuated and mounted to the top outer edge of the cylinder head it extends straight up and will work on almost all model years. Se

part no: 13H5506

PIVOT PIN LOWER ARM
Pre-owned (used) product that functions that same as the new one pictured. This is the front suspension lower support shaft, which fits into the the front subframe to provide the inner pivot mountin

part no: U/21A1889

MINI & COOPER TWIN LEADING BRAKE KIT DRUMS AND SHOES
Most Minis with drum brakes on the front of the car have the 'twin leading' type. This means not only are there two seperate brake wheel cylinders per wheel but most important the brake shoes are 1 1

part no: MMKT0511

LAYGEAR 22G927 4SYNC
This is a Pre-Owned (USED) transmission Laygear as used on 4 sync wide ratio pre A+ gearboxes. The availability of this pre-owned (used) part is subject to change at any time. This part should not b

part no: U/22G927

PILLAR FOR ADJUSTING BRACKET ON ALTRNATOR OR GENERATOR
This pillar is threaded on both ends and mounts to the engine plate on one end and alternator/generator adusting bracket on the other end.

part no: 2A128

MINI & COOPER KYB FRONT SHOCK ABSORBER GAS UPGRADED DAMPER
These are KYB 25% upgrade on their KYB standard oil damper. Beware of others who claim 25% upgrades - they do not know always state what they are 25% upgrades of. We have tried and tested every shock

part no: 342001

HEADLIGHT HEADLAMP CLIP, SCREW type

part no: 37H7421A

SEALED BEAM 7" HEADLAMP HEADLIGHT (WIPAC) - RHD
The original sealed beam incandescent headlight. Sealed beam with a clear spot area for pilot light to shine through,probably the most common Left hand drive light unit used on cars up to 1990.For RHD

part no: 13H3471A

TWIN TUBE GAS FILLED ADJUSTABLE SHOCK ABSORBER FRONT
The New Evolution AGX shock absorber is a twin tube type and gas filled. Fully adjustable in 8 steps without having to be removed from the car. This is currently the shortest fitted length damper we s

part no: 743039

TWIN TUBE GAS FILLED ADJUSTABLE SHOCK ABSORBER REAR
The New Evolution AGX shock absorber is a twin tube type and gas filled. On car 8 point adjustable. Most dampers available are only mono tube except for Koni so this item takes you into the next stage

part no: 743040

K&N AIR FILTER CARE KIT - CLEANER AND OIL
To get the maximum benefit of K&N filters they should be cleaned periodically. This filter care service kit is a six-step maintenance system to recharge your K&N Filtercharger air filter. Includes a 1

part no: 99-5000

K&N FILTER CARE KIT PUMP SPRAY OIL - CLEANER AND OIL
To get the maximum benefit of K&N filters they should be cleaned periodically. This filter care service kit is a six-step maintenance system to recharge your K&N Filtercharger air filter. Includes a 1

part no: 99-5050

THROTTLE ACCELERATOR CABLE TRUNNION
Threaded side has hole for throttle cable. Nut clamps cable. Untreaded side fits through throttle linkage and is attached with cotter pin, and usually holds one end of a trottle return spring. Common

part no: ACC5062

TRUNNION PIN KIT FOR THROTTLE ACCELERATOR CABLE
If you are working on throttle cable or even just the carb itself and find that the end that attaches to the carb is a bit of a make-shift set-up, then this original style connector should do the job.

part no: ACC5062K

MOKE DRIVERS H/BOOK
Reproduction of Driver's Handbook for the English produced Mini Moke. Originally issued as a supplement to go with the Morris/Austin Mini Driver's Handbooks, AKD 3886/7.

part no: AKD4130

MINI MOKE WING LEFT FRONT TRUNKING DIAGONAL TOP CAPPING

part no: ALA7032

WING RIGHT FRONT-TRUNKING TOP CAPPING

part no: ALA7033

MOKE FRONT WING - RIGHT HAND
This part of a Moke front fender is designed for Mokes with extentions on them - but it can also be fitted to any Moke with minor work.

part no: ALA7070

MOKE FRONT WING - LEFT HAND
This part of a Moke front fender is designed for those mokdes that had the extentions on them but can also be fitted to any Moke with minor work!

part no: ALA7071

SIDE COVER MOKE
All Moke owners will know how critical this almost flat piece of sheet metal really is! The side pontoons of the Moke not only form the backbone of the body but the hollow cavities also make a great

part no: ALA7164

LOWER WINDSCREEN RUBBER FOR MOKE
Replacing the windshield rubber in a Moke is one of the easier jobs. The frame for the glass is bolted together and thus easy to disassemble. The rubber seal for the glass is actually in two pieces,

part no: ALA7230

MOKE SIDE PANEL - RIGHT HAND
The side panels of the any Moke are very prone to rust and thus a complete replacement from any model is step in the right direction. These right side panels can with a little work be fitted to any m

part no: ALA7310

FUEL PUMP MECHANICAL MINI AND MINI COOPER To 1990
The later models of the Mini (after about '73) use a mechanical fuel pump driven off the camshaft at the rear of the motor. These pumps are generally reliable but when a diaphragm goes bad it can be

part no: AZX1818

CLIP HEADLAMP HEADLIGHT BEZEL
The chrome headlamp bezel on your car should be held in place with a small screw on the bottom. This screw is intended to connect to a small Clip that fits over a tab on the headlamp bucket. This is

part no: BAU1460

MOKE - LOGO 'Moke' - GREY
Go ahead - challenge people to ask about your car! As used on later model Moke, this logo can be placed almost anywhere. High quality metalic vinyl, silver with charcoal background; 13 1/2 x 1 7/8 inc

part no: BHM9524

WIPER MOTOR with DRIVE
Nothing increases the likelihood that your wipers will work more than replacing the wiper motor with a NEW one! These genuine Lucas 2-speed wiper motors are applicable to all MKII and onwards (includi

part no: BHM9533

MOKE REAR PANEL
Of all the panels on a Moke the very rear vertical panels is the least likely to rust but also is the most likely to be damaged in a rear end collision!

part no: BHM9644

MOKE BATTERY BOX DOOR - HINGED
The Moke battery box can be open from the top or the side. The side panel that always rusts or corrodes is available in two types; the version that is simply bolted to the side panel and this version

part no: BHM9659

MOKE REAR WING - LEFT HAND
Mokes in general have very simply panel construction but it is still often easier and much cheaper to replace the offending piece than it is to try to repair it. This rear fender along with most Moke

part no: BHM9692

MOKE LOGO BADGE 'Moke' - RED

part no: BHM9812

ALLOY ALUMINUM HEAD ASSEMBLED WITH VALVES AND SPRINGS
We are proud to offer the C-AHT345 cylinder head fully assembled and ready to bolt on! This includes "ST" dual springs, new valves, retainers, keepers and studs. The rocker assembly is not included; w

part no: MMKT0600

Swiftune 1.5 RATIO ALUMINUM ROLLER TIPPED ROCKER GEAR
All aluminum roller rockers are not the same. Recent testing has show most all aluminum roller tipped rockers have enough flex in them that valve lift is lost at anything above 7,000 RPM. These specia

part no: C-AHT447

VERNIER BELT CAM DRIVE KIT FOR CAMSHAFT - MINI COOPER ETC.
Belt drive kit with screw type variable adjustment. A full kit to convert your timing gears to a belt driven type to restore power loss caused by original timing gear wear and stretching. Also helps

part no: C-AJJ3326

HI/LO TYPE KIT Front & Rear Budget kit MINI & MINI COOPER S
Hi-Lo Suspension Kit Includes all four Hi-Lo trumpets plus the two extended aluminum struts required for the rear. Many people will tell you why you should consider upgrading to the classic "Hi/Lo" su

part no: C-STR644

WHEEL LUG NUT CHROME ACORN LONG STOCK RADIUSED TAPER
Chrome Lug nut Sold Individually (4 required per wheel) Fit stock 10" wheels. Also fits Minitor and other Mag wheels that take a stock, tapered lug nut. For the same type lug with a wider contact s

part no: CN1/EA

UNION JACK WITH CHECKERED FLAG DECAL STICKER PAIR
Metalized rigid plastic decal showing the Union Jack and checkered flags. Adhesive backed, approx. 1 3/4-in. wide. Two decals per pack.

part no: DECAL38

MINIMANIA.COM DECAL STICKER LARGE - 4.5 X 11"
Dress up your MINI with our Mini Mania logo! A large 4.5" x 11" black cut vinyl graphic shows nicely on all light colored MINIs. Vinyl material goes on easy and can be removed if necessary.

part no: DECAL39

MINIMANIA.COM DECAL STICKER LARGE WHITE 4.5 x 11"
Dress up your MINI with the Mini Mania logo! A large 4.5" x 11" white cut vinyl graphic shows nicely on all colors – except for white. Vinyl material goes on easy and can be removed if necessary.

part no: DECAL40

POWERED BY MINIMANIA - DECAL
Clear poly exterior decal, 1.5" x 6", sets your Mini apart as being "Powered by Mini Mania"!

part no: DECAL41

TUNING THE A-SERIES ENGINES 3rd ed (VIZARD/HAYNES)
"Tuning BL's A-Series Engine" by David Vizard This 3rd edition of the bible for all A-series engines was completed in 1999. THE latest and great from David Vizard. This book has tremendous upda

part no: F732

TWIN HS2 W/MANIFOLD
This complete New twin 1 1/4" SU carb set-up will solve many problems! There are times when it is not too difficult to fix a part- but there are also times it is much better to just replace it! Deal

part no: FZX3052

VOLTMETER 9-17 VOLTS by REVOTEC
By watching the output of your battery you can probably avoid a disaster!

part no: G-V

GOPRO MOTORSPORTS HERO DIGITAL VIDEO CAMERA WIDE ANGLE
The world's smallest, wireless on-board video camera! High Quality, Versatile, EASY-to-use "point-shoot" style digital video camera designed for harsh environments. The Motorsports HERO W

part no: G2NMA4000

FRONT WHEEL BEARING KIT ROLLER TAPER S
The front wheel bearings for the Cooper "S" were all originally these 'roller' bearing style. The design of the roller rather than the more common ball bearing is such that they will last much longer

part no: GHK1140

Clutch Master cylinder upgrade kit early Mini and Cooper
Clutch Master Cylinder Repair kit for pre 1985 models- this kit has been amended to allow the upgrade of the early (full base cup) master cylinder to the later and improved ring seal design. Instruct

part no: GRK3007

STANDARD TUBE SHOCK MINI & COOPER FRONT & CONVERSIONS
Standard tube shock for front of Mini or Mini Cooper. These factory original type shocks will gives years of service to normal road use fro any Mini or Mini Cooper. Shocks are designed to keep the ti

part no: GSA388

SHOCK REAR STANDARD MINI & COOPER and CONVERSIONS
Standard tube shock for rear of Mini.

part no: GSA389

LUCAS QUALITY INSPECTOR HAT
High-quality, all-cotton "low profile" hat, Tan with Black Brim. Adjustable band, one size fits all.

part no: HAT14

MOKE WINDSCREEN FRAME
Don't be deceived by this picture- all Moke window frame have the same dimensions. A few extra studs from this type to the more common English Moke type but if yours is rusted or bent- this is the be

part no: HYE0949A

MOKE REAR FLOOR
When restoring a Moke the ability to replace any single panel is a real plus. This is the panel that the two rear seats mount to. Not difficult to replace considering the size!

part no: HYE1144B

MUDFLAP MOKE REAR, PAIR, EMBOSSED - MOKE
While very popular on the Australian Mokes these "Moke" embossed mud flaps are a great addition to any Moke. Designed to fit on the rear of the car, these are great heavy duty rubber guards! Sold as

part no: HYE1174

MOKE ITALIAN FRONT PANEL
While all Mokes are very similar, there were several changes made depending on the original plant in which they were made. The front panels all look very similar and thankfully any of them can be made

part no: HYK4209A

KEY BLANK FP SERIES OR 62DP
Any locksmith can cut you a key, but the odds of him having a blank are pretty slim! We import key blanks to suit early British cars.

part no: KEY2

LAMP BASE MINI MOKE AND FRONT >63 MINOR TURN SIGNAL
Almost all English Mokes use a very large front turn signal for safety and design. This assembly is also prone to corrosion and rust. This is the base assembly that holds the lens. The later model

part no: LMP174

KENT MEGADYNE 310 CAM A+ DRIVE
Kent Cams full race Camshaft in Slot Drive

part no: MDM310

MKI & II IGNITION TUNE UP KIT for 25D Distributors
This exclusive Mini Mania kit includes not only the parts needed to tune up your classic Mini but even the great Haynes how-to do it book! All early cars with side entry distributor caps could use th

part no: MMKT0027

WATER PUMP, BELT AND 11 BLADE FAN KIT MINI & MINI COOPER
This great kit includes a high capacity water pump, high efficiency 11 blade plastic fan and the appropriate fan belt. It's warmer here than in the UK. This higher capacity water pump moves more coola

part no: MMKT0139

HIF4 CARB CONVERSION MINI & MINI COOPER

part no: MMKT0141

STOCK COOPER S STYLE RADIATOR WITH 6 BLADE TROPICAL FAN
The original stock Mini Cooper "S" radiator was this very efficient 3-core design. This radiator is s direct replacment in all Mini and Mini Coopers. With the addition of the metal 6-blade 'tropical

part no: MMKT0144

HEADLIGHT HEADLAMP CHROME RING KIT per car MINI MINI COOPER
Includes two 500929MS trim rings and two 515218A inner rings (the ones that hold the bulbs in place).

part no: MMKT0214

BRAKE CONVERSION KIT MINI COOPER TO MINI COOPER S
Convert from small discs to Cooper S disc brakes, the largest used on 10" wheels. Kit includes: (2) GCV1013=CV Joints, 1300cc/S, New (2) 18G9027MS=CV Boot Kits (2) 21A1270=Drive Flange, S (2)

part no: MMKT0509

IGNITION REBUILD KIT FOR 25d DISTRIBUTOR
Ignition tune-up kit, includes: RA1/DRB101=Rotor pre71 C1/DCB101=Condenser pre71 GCS101=Points pre71 54413549=Low Tension Lead Note that this kit does NOT include the dizzy cap (order top- or

part no: MMKT0702

EARLY IGNITION TUNE UP KIT (SIDE ENTRY DIST CAP)
Basic ignition tune-up kit with side-entry distributor cap, includes: DC1/DDB101=Side Entry Distributor Cap RA1/DRB101=Pre'74 Rotor Arm GCS101=Pre'74 Points C1/DCB101=Pre'74 Condenser LHT753

part no: MMKT0704

IGNITION TUNE UP KIT 45D DISTRIBUTOR '74-'80
Basic ignition tune-up kit for all engines from about 1974. The distributor should have a '45D' marked on it and the points have a distinctive red block. Kit includes points, rotor, condenser, plugs

part no: MMKT0707

IGNITION TUNE UP KIT WITH SHOP MANUAL FOR '74-'80 45D DIST
Basic ignition tune-up kit for all engines from about 1974. The distributor should have a '45D' marked on it and the points have a distinctive red block. Kit includes points, rotor, condenser, plugs a

part no: MMKT0712

IGNITION TUNE UP KIT AND SHOP MANUAL FOR 1980 AND LATER
Basic ignition tune-up kit for engines after 1980 and before Fuel injected. Approx 1980 thru 1989 that use the 59D distributor. The points typically have a distinctive blue plastic block in them. Kit

part no: MMKT0713

IGNITION TUNE UP KIT 59D DISTRIBUTOR 1980 AND LATER
Basic ignition tune-up kit for engines after 1980 and before Fuel injected. Approx 1980 thru 1989 that use the 59D distributor. The points typically have a distinctive blue plastic block in them. Kit

part no: MMKT0708

SPARE FUSE PACK INCLUDES 15 AND 25 AMP FUSES
In the event the 'prince of darkness' strikes your Mini, this kit will simplify keeping your lights on, by helping you keep a few spare fuses in your car. Includes three 15 amp and three 25 amp fuses.

part no: MMKT0709

ELECTRONIC IGNITION UPGRADE FOR MINI & MINI COOPER
Electronic ignition upgrade kit for your 25D distributor as found in most early Mini & Mini Coopers. This kit includes a Pertronix Ignitor module that replaces the stock mechanical points, a new match

part no: MMKT0710

ELECTRONIC IGNITION UPGRADE KIT- 45D DISTRIBUTOR MINI COOPER
Electronic ignition upgrade kit for your 45D distributor (with red fixed points) as found in many Mini & Mini Coopers. This kit includes a Pertronix Ignitor module that replaces the stock mechanical

part no: MMKT0711

REVERSE LOCKOUT FOR MINI & MINI COOPER
Reverse gear lockout for remote type gearlevers to remove possibility of going into reverse in error. Very easy to deactivate for street or panic needs on the race track!

part no: MS71

EMBLEM UNION JACK
Great looking plastic emblem that is well suited for use on shift knobs, key fobs and even wheel center caps! Easy self sticking backing included. Approximately 1" diameter

part no: MSA2004

ULTRIK MOBILITY KIT - COMPRESSOR, TIRE SEALANT AND BAG
If your little car is not running on run-flat tires and you don't have the space or desire to carry a spare wheel and tire- then this kit is for you! The ULTRIK Mobility Kit contains a 12v compressor

part no: NMA4015

MINI MANIA KEY RING
If you love your MINI, then you need this stylish chrome key chain with the Mini Mania "MM" logo. A great gift idea!

part no: NMA6010

WHEEL SPACER SET FRONT PAIR (.500) MINI COOPER
1/2 WHEEL SPACERS, SOLD AS PAIR ONLY. These wheel spacers have been specially modified to the fit the front or rear of all Minis and Mini Coopers with drum or disc brakes. Just enough addtional offs

part no: NMW4001

PECO LARGE BORE STRAIGHT SINGLE CHROME TIP OUTLET
The name Peco has long been associated with the manufacture of high quality 'Big Bore' sports exhaust systems and back boxes, at amazingly affordable prices. This muffler has a large bore inlet pip

part no: PECO-BB1-2

PECO SMALL BORE TWIN PIPE EXIT MUFFLER
The name Peco has long been associated with the manufacture of high quality 'Big Bore' sports exhaust systems and back boxes, at amazingly affordable prices. The Company was originally formed in 1964

part no: PECO-BB1-3T

PECO REAR BOX WITH PIPE TO CATALYST
This complete exhaust system from Peco provides a B pipe that extends from the stock cat to the performance Peco muffler with a single round 64mm chrome tip outlet!

part no: PECO-BB2

RING COMPRESSOR TOOL 1275cc +.020
Tired of breaking piston rings? For many years now the guys that run Chevy or Ford motors have had the luxury of using this almost fool proof means of installing your pistons with rings into the bloc

part no: PHED20

RING COMPRESSOR TOOL 73.5mm
Tired of breaking piston rings? For many years now the guys that run Chevy or Ford motors have had the luxury of using this almost fool proof means of installing your pistons with rings into the bloc

part no: PHED735

RING COMPRESSOR TOOL 1275cc +.040
Tired of breaking piston rings? For many years now the guys that run Chevy or Ford motors have had the luxury of using this almost fool proof means of installing your pistons with rings into the bloc

part no: PHED40

RING COMPRESSOR TOOL 1275cc +.060
Tired of breaking piston rings? For many years now the guys that run Chevy or Ford motors have had the luxury of using this almost fool proof means of installing your pistons with rings into the bloc

part no: PHED60

"GB" LAPEL PIN
"GB" cloisonne lapel pin. Pin measures appoximately 1" x 3/4".

part no: PIN03

BMC DRIVERS CLUB PIN
Enameled pin, approx. 7/8" high.

part no: PIN38

UJ LICENSE PLATE
These real looking u. s. sized license plates are stamped from metal and printed in the appropriate colors. A nice touch for the front of the car or the wall of the garage!

part no: PLATE02

ADJUSTER REAR BRAKE 803 & 948 MODELS '54 - 62
This is the small half elliptic piece that you engage with your screwdriver to adjust your rear brakes. The outer edge is suppose to provide a course rachet for maintaing adjustment. If you are havi

part no: RBK112

TACHOMETER POD for 80mm / 3" CHROME
Chrome pod for housing any of the popular size 80mm tachometers from either Smiths or Tim gauges.

part no: SIB801

PRE-OWNED FRONT PULLEY BOLT - USED

part no: U/12A283

3 SYN REVERSE GEAR SHAFT

part no: U/88G209

FUEL PUMP MECHANICAL HIF38 MINI 1992-1994
For 1275cc engines after 1990 on with HIF38 carbs. has a 5/16" inlet which makes it unique to this model The later 1990 on models of the Mini with 1275cc engines and HIF44 carbs use a AZX1817 mechanic

part no: WND10005

FUEL PUMP MECHANICAL 998 NON GENUINE
Non Genuine version mechanical fuel pump Drives off the camshaft at the rear of the motor. These pumps are generally reliable but when a diaphragm goes bad it can be very bad as often raw gas is pumpe

part no: AZX1818MS

MOKE FRONT BADGE RAISED LETTERS

part no: BHM9564

WHEEL LUG NUT ACORN STOCK RADIUSED TAPER BRUSHED FINISH EACH
Silver matte finish Lug nut SOLD INDIVIDUALLY (4 required per wheel) Fit stock 10" wheels. Also fits Minitor and other Mag wheels that take a stock, tapered lug nut. For the same type lug with a wi

part no: CN1/B

GREEN ENGINE PAINT 500ML TIN SUITABLE FOR BRUSHING
Green Engine Paint", maintenance can mean more than mechanical. Even if you don't rebuild it, painting it can at least make it look new! And if you actually are rebuilding the motor, you are sure to w

part no: GAP409

FUEL PUMP MECHANICAL 1275cc MINI 1990 >
1990 on models of the Mini with 1275cc engines and HIF44 carbs use a different mechanical fuel pump. Driven off the camshaft at the rear of the motor these pumps are generally reliable but when a diap

part no: AZX1817

ALLOY RADIATOR MOUNTING BLOCK BRACKET
Pre-owned (used) Alloy bracket on the end of the gearbox for the lower radiator bracket 12A361 to mount on to. The availability of this pre-owned (used) part is subject to change at any time. This p

part no: U/12G1318


www.minimokeusa.com